LG LFDS22520S Dimension Manual

The LG LFDS22520S is a 22 cubic foot top-freezer refrigerator featuring a sleek design, adjustable glass shelves, humidity-controlled crispers, a full-width gallon door bin, and LED lighting. This manual provides detailed dimensional specifications, installation requirements, and clearances necessary for proper setup and integration into your kitchen space. Below are key sections covering overall dimensions, installation clearances, door swing requirements, and space planning guidelines.

1. Overall Dimensions 2. Installation Clearances 3. Door Swing & Handle Clearance 4. Cutout & Recess Specifications 5. Weight & Load Distribution 6. Ventilation Requirements 7. Leveling & Alignment 8. Built-In Considerations 9. Moving & Handling 10. Safety Precautions 11. FAQ & Troubleshooting

Overall Dimensions

Key external measurements for planning refrigerator placement.

Dimension Type	Measurement (inches/mm)
Height (Overall)	68.9 in / 1750 mm
Width (Overall)	33.0 in / 838 mm
Depth (Overall with door closed)	34.4 in / 874 mm
Depth (Overall with door open 90°)	56.5 in / 1435 mm
Depth (Without handle)	32.5 in / 826 mm
Door Handle Projection	1.9 in / 48 mm

Installation Clearances

Minimum required spaces around the refrigerator for proper operation and ventilation.

Top Clearance: Minimum 1 inch (25 mm) between top of unit and overhead cabinets or ceiling.
Side Clearances: Minimum 0.25 inch (6 mm) on each side if installing between cabinets or walls.
Rear Clearance: Minimum 2 inches (51 mm) from back wall to allow for airflow and connections.
Floor Clearance: Ensure floor is level within 0.25 inch (6 mm) over refrigerator width.

WARNING! Insufficient clearances can cause overheating, increased energy consumption, and potential component failure.

Door Swing & Handle Clearance

Space required for door operation and access.

Door Swing Arc: Requires clearance for 105-degree opening for full access to bins and shelves.
Handle Clearance: Account for additional 1.9 inches (48 mm) beyond door depth when measuring.
Adjacent Obstructions: Ensure no walls, cabinets, or appliances block the door swing path.
Reversal Instructions: Door swing can be reversed; refer to separate installation guide for steps.

CAUTION! Verify door swing direction matches kitchen layout before final positioning.

Cutout & Recess Specifications

Cabinet Opening Width: Minimum 33.5 inches / 851 mm recommended for side clearance.
Cabinet Opening Height: Minimum 69.5 inches / 1765 mm recommended for top clearance.
Depth of Recess: Cabinets or enclosures should be at least 34.5 inches / 876 mm deep.
Kick Plate Recess: Ensure base cabinets allow for refrigerator toe kick; height 4 inches / 102 mm.
Water Line Access: Locate water inlet valve at bottom rear; allow 6 inches / 152 mm access space.

Weight & Load Distribution

Total weight and floor loading requirements.

Net Weight: 154 lbs / 70 kg. Shipping Weight: 168 lbs / 76 kg.

Floor Load: Ensure floor can support concentrated load. Distribute weight evenly using leveling feet. Moving: Use appliance dolly; protect floor with cardboard. Leveling: Adjust front leveling feet to ensure door closes properly and unit is stable.

Ventilation Requirements

Critical airflow specifications for compressor and condenser operation.

Maintain all minimum clearances listed in Section 3.
Do not block grille at bottom front or rear of unit.
Ensure room ambient temperature is between 55°F (13°C) and 110°F (43°C).

Tip: Poor ventilation is the leading cause of cooling performance issues. Never install in a closed alcove without adequate airflow.

Leveling & Alignment

Steps to ensure refrigerator is level for proper door operation and cooling.

Place refrigerator in final location before removing shipping materials.
Use a carpenter's level on top from front to back and side to side.
Turn leveling feet clockwise to raise, counterclockwise to lower.
Check that doors self-close from a 3-inch open position when properly leveled.
Re-check leveling after 24 hours as unit settles.

WARNING! An unlevel unit can cause door alignment issues, improper sealing, and increased energy use.

Built-In Considerations

This is a freestanding model, not designed for true built-in installation.

Flush Installation: Can be installed flush with standard 24-inch deep cabinets, but door will protrude. Panel Ready: Not compatible with custom front panels. Heat Dispersal: Freestanding models disperse heat differently than built-in; maintain required clearances.

Moving & Handling

Guidelines for safe relocation.

Preparation: Remove all food and shelves. Secure doors with tape. Transport: Keep unit upright. Tilting beyond 45° can cause compressor oil migration. Resting: If laid on side, let stand upright for 24 hours before plugging in.

CAUTION! The refrigerator is heavy. Use proper lifting techniques and equipment. Two-person lift is required.

Safety Precautions

FAQ & Troubleshooting

Issue	Possible Cause	Corrective Action
Doors won't close properly	Unit not level	Re-level the refrigerator front-to-back and side-to-side.
Warm interior temperature	Insufficient clearance	Verify all minimum clearances (top, sides, rear) are met.
Vibrations or noise	Uneven floor or touching cabinets	Ensure unit is level and not in contact with surrounding surfaces.
Water leakage	Improper connection or clog	Check water line connection at valve and ensure filter is installed correctly.
Door handles misaligned	Shipping brackets not removed	Confirm all packaging and shipping bolts/braces have been removed.

Reset: Unplug unit for 5 minutes to reset control board if display malfunctions.

Service: 1-800-243-0000; www.lg.com